中文版| English| Français| 한국어| Русский| Español| لعربية | Português |

homeMarketing Center

Online Consultation

Contact us

  • Mr Jason Chen
  • 河北分部:+86-10-80841942/64
    深圳分部: +86-755-33134503
  • 河北分部:+86-10-80841942
    深圳分部:+86-755-36610305
  • bjreci@recilaser.com
  • Hebei: 51 Panoramic Industrial Park, No.10 Liushan Street, Yanjiao Development Zone, Langfang City, Hebei, China
    Shenzhen:Floor1.building23.Alley1,
    Mashan,Fuyong,Bao An District, Shen Zhen. Guangdong, P.R.China

CO2 Laser Tube

Views:49852
CO2 Laser Tube

Mark & model  :  W2, The product is featured as small size and good model, higher power rate compared with the laser tube of similar length and longer service time, which is suitable for laser marking, laser cutting and laser engraving.

Origin  :  Asia and Pacific Area  China

Quality standard  :  International

Submit date  :  2012-11-28

H.S.Classification  :   Machinery & Electronics  Electr.Element  8541 Semiconductor devices; light-emitting diodes etc.; parts thereof

Feedback

Product profile  :  CO2 Laser Tube

1. 1.Installation Requirement 
Make sure to follow the operation instruction of model W2 as shown in the illustration. The dedicated power 
P12 should be equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 19kv). 
It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube 
will be punctured by electricity and may cause water leakage. 

 

2. 2.Operation conditions Water cooling: using purified water; 2 to 5 liter/minute; 
water temperature: 10
-40.
 
The operating environment: temperature 2-40; humidity 10-60%.
The working current: test current is 29mA. Maximum working current is 29mA. The running current 
must be kept below 27mA. The life span can reach 
8,000 hours if the current is kept below 25mA. 
The ammeter must be connected to the negative electrode of laser tube.
When it is working under over-high current for long term, the negative pole will appear light yellow and the life span will be shortened rapidly.
To protect dust from going into the insulation sheath, please wrap it with plastic film.

 

3. 3.Working Performance 
Cutting function.

Engraving function: Very good. When the working current is 4mA and the tube is in the state of preionization, 
the laser can be used for high-frequency impulse engraving.

 

4. 4.Key Notes 
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise 
the output power will be seriously affected. The followings are the designated methods to 
clean up pollution in the exterior surface of window mirror: 

1) When the mirror is polluted, do not turn on the laser.

2) Blow the mirror surface sideways with an air blower. 

3) Spray the pure alcohol on the mirror surface with sprayer.

4) Turn on the laser after the alcohol gets fully volatilized. 

5) If the methods above don't work effectively, it is necessary to ask for the professional 
to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution 
is to prevent the window from being polluted. 

Attention: it is forbidden to clean the mirror with acetone.

The screws in the front and back ends of the laser tube are not allowed to be moved, 
otherwise the output power will be declined, even the tube will be scrapped.

Put the acryl 300mm far away from output mirror, when testing its laser spot.

5.Safety 

The laser beam is invisible light. Please wear protective glasses when debugging the laser. 
The positive pole is in high voltage. Pay attention to the security marks.

6.Storage and Transportation Requirement 

Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40, and the requested humidity is 10-60%. Pack the laser as in the original way. 

Important notes: it is requested to use adhesive tape to cement the sponge together with laser tube 
to prevent the tube from vertically sliding during transportation. The sponge in the side of output mirror 
must be 70 mm beyond it, and the sponge in the side of reflecting mirror must be 50 mm wider. 

 

7. 7.Tubes operated in wrong way are not guaranteed by Manufacturer. 

Beijing Reci Laser Technology Co., Ltd.

 


    Cardboard Carton  Package Size

 
 

MODEL

N.W(KG)

G.W(KG)

 CARTON(CM)

WOODEN CASE(CM)

CHARING WEIGHT(KG)

W1

3

4.5

136×24×24

138×26×27

20

W2

3.5

5

136×25×25

138×27×28

21

W4

4

7

156×38×38

159×41×42

55

W6

5

8

180×38×38

183×41×42

63

W8

6

11

201×40×40

204×44×46

83

 

   Laser Tube basic parameter

MODEL

RATED POWER

MAX POWER

LENGTH(mm)

DIA

(mm)

CATALYZE

LIFE SPAN (h)

WARRANTY

W1

75W

90W

1050

80

YES

10000

10MONTHS

W2

90W

100w

1200

80

YES

10000

10MONTHS

W4

100W

130w

1400

80

YES

10000

10MONTHS

W6

130W

160w

1650

80

YES

10000

10MONTHS

W8

150W

180w

1850

90

YES

10000

10MONTHS

Message

*E-mail
*Telephone
*Contact
Submit
More

Related Products

  • CO2 Laser Tube

    CO2 Laser Tube

    W2, The product is featured as small size and good model, higher power rate compared with the laser tube of similar length and longer service time, which is suitable for laser marking, laser cutting and laser engraving.
  • co2 lasers

    co2 lasers

    W4, The product is featured as high power rate, good model, fast-speed cutting and small size, which is used for the cutting of leather, cloth and processing of lampshade and handicraft.
  • CO2 Laser Device

    CO2 Laser Device

    W6, The product is featured as cutting of large power rate and long service time, which is suitable for the cutting of knife mold machine and thick acrylic sheet.
  • Laser Equipment Part

    Laser Equipment Part

    W8, The product is featured as large power rate laser tube, good stability and fast cutting speed, which is suitable for the cutting of thin metal plate.